Wiki Documentation Site

User Tools

Site Tools

You are here: Main Page » visual3d » tutorials » modeling » Virtual Laboratory
visual3d:tutorials:modeling:virtual_laboratory

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:tutorials:modeling:virtual_laboratory [2026/02/06 19:30] – [Example: Creating a virtual laboratory that changes with the direction of walking] wikisysopvisual3d:tutorials:modeling:virtual_laboratory [2026/06/02 14:56] (current) – ↷ Links adapted because of a move operation 114.119.143.145
Line 7: Line 7:
 A Virtual Laboratory is not a physical segment in Visual3D but is equivalent to a physical segment to the effect that it has a Segment Coordinate System that can be used to represent the laboratory (or other objects) and has an associated surface model that can be animated as part of the scene. A typical use of the Virtual Laboratory is to represent the floor so that motion capture markers can be projected onto the floor. A Virtual Laboratory is not a physical segment in Visual3D but is equivalent to a physical segment to the effect that it has a Segment Coordinate System that can be used to represent the laboratory (or other objects) and has an associated surface model that can be animated as part of the scene. A typical use of the Virtual Laboratory is to represent the floor so that motion capture markers can be projected onto the floor.
  
-**Note:** A typical use of the Virtual laboratory is for creating [[Visual3D:Documentation:Pipeline:Model_Based_Data_Commands:Joint_Angle#Joint_Angle_Normalization|Normalized Joint Angles and Normalized Segment Angles]].+**Note:** A typical use of the Virtual laboratory is for creating [[visual3d:documentation:visual3d_signal_types:link_model_based_data_type:joint_angle#Joint_Angle_Normalization|Normalized Joint Angles and Normalized Segment Angles]].
  
 Below is a straightforward virtual lab that has a specified constant orientation. Below is a straightforward virtual lab that has a specified constant orientation.
Line 182: Line 182:
 \\ 3. Select the **Create** button     \\ 3. Select the **Create** button    
  
-4. In the **Virtual Lab** tab, enter these values:\\ \\    **Define Proximal Joint and Radius**\\ \\    **Lateral:** //None//     **Joint:** //Lab_Z//     **Medial:** //None//     \\ \\    **Radius:** //0.01//\\ \\    **Define Distal Joint and Radius**\\ \\    **Lateral:** //None//     **Joint:** //Lab_Origin//     **Medial:** //None//     \\ \\    **Radius:** //0.01//\\ \\    **Extra Target to define Orientation**\\ \\    **Select:** //Lateral//     //Lab_Lateral//\\ \\    **Select Tracking Targets:**\\ \\       **Check:** //Use Calibration Targets for Tracking//  \\ \\ 5. Click on **Build Model.**\\ \\ 6. Click on **Close Tab** before proceeding.    {{:VLab_SegmentDefinition_Ex3VLabwrtDirection.jpg}}+4. In the **Virtual Lab** tab, enter these values:\\ \\    **Define Proximal Joint and Radius**\\ \\    **Lateral:** //None//     **Joint:** //Lab_Z//     **Medial:** //None//     \\ \\    **Radius:** //0.01//\\ \\    **Define Distal Joint and Radius**\\ \\    **Lateral:** //None//     **Joint:** //Lab_Origin//     **Medial:** //None//     \\ \\    **Radius:** //0.01//\\ \\    **Extra Target to define Orientation**\\ \\    **Select:** //Lateral//     //Lab_Lateral//\\ \\    **Select Tracking Targets:**\\ \\       **Check:** //Use Calibration Targets for Tracking//  \\ \\ 5. Click on **Build Model.**\\ \\ 6. Click on **Close Tab** before proceeding.    {{ :VLab_SegmentDefinition_Ex3VLabwrtDirection.jpg}}
  
 \\ \\
visual3d/tutorials/modeling/virtual_laboratory.1770406245.txt.gz · Last modified: by wikisysop