visual3d:tutorials:modeling:plug-in_gait_lower_limb
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| visual3d:tutorials:modeling:plug-in_gait_lower_limb [2024/12/10 14:34] – [Load Static Trial] wikisysop | visual3d:tutorials:modeling:plug-in_gait_lower_limb [2025/05/20 15:13] (current) – wikisysop | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Plug-In Gait Lower Limb ====== | ====== Plug-In Gait Lower Limb ====== | ||
| - | **N.B. While every effort has been made to ensure the correct implementation of the Plug-In Gait model in Visual3D, some differences may still persist, most likely caused by the different pose estimations used within Nexus and Visual3D. Please report any errors to support@has-motion.com.** | + | **N.B. While every effort has been made to ensure the correct implementation of the Plug-In Gait model in Visual3D, some differences may still persist, most likely caused by the different pose estimations used within Nexus and Visual3D. Please report any errors to support@has-motion.ca.** |
| **NOTE:** This tutorial has been updated. The original format can be found [[Visual3D: | **NOTE:** This tutorial has been updated. The original format can be found [[Visual3D: | ||
| Line 101: | Line 101: | ||
| - From the **Model** menu, select **Hybrid Model from C3DFile** | - From the **Model** menu, select **Hybrid Model from C3DFile** | ||
| - | - In the **Select the calibration file for the new model** dialog, select //Sub01_Static_01.c3d// | + | - In the **Select the calibration file for the new model** dialog, select //WalkingStaticLowerBody.c3d// |
| - If using a knee alignment device, select // | - If using a knee alignment device, select // | ||
| - Click **Open.** | - Click **Open.** | ||
| Line 191: | Line 191: | ||
| - Click **Landmarks** button | - Click **Landmarks** button | ||
| - Click **Add New Landmark** button | - Click **Add New Landmark** button | ||
| - | - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\ Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/ | + | - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\ Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/ |
| ---- | ---- | ||
| Line 200: | Line 200: | ||
| - Click **Landmarks** button | - Click **Landmarks** button | ||
| - Click **Add New Landmark** button | - Click **Add New Landmark** button | ||
| - | - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\ Click **Existing Segment:** // | + | - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\ Click **Existing Segment:** // |
| ---- | ---- | ||
| Line 239: | Line 239: | ||
| - In the **Segments** tab, select //Right Thigh// in the Segment Name box. | - In the **Segments** tab, select //Right Thigh// in the Segment Name box. | ||
| - Click on the **Create Segment** button. | - Click on the **Create Segment** button. | ||
| - | - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\ **Lateral: | + | - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\ **Lateral: |
| - Click on **Build Model.** | - Click on **Build Model.** | ||
| - Click on **Close Tab** before proceeding. | - Click on **Close Tab** before proceeding. | ||
visual3d/tutorials/modeling/plug-in_gait_lower_limb.1733841266.txt.gz · Last modified: 2024/12/10 14:34 by wikisysop