HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » tutorials » modeling » IOR Foot Model 2007
visual3d:tutorials:modeling:ior_foot_model_2007

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:tutorials:modeling:ior_foot_model_2007 [2024/07/03 17:45] – created sgrangervisual3d:tutorials:modeling:ior_foot_model_2007 [2024/07/17 15:47] (current) – created sgranger
Line 1: Line 1:
-====== IOR_Foot_Model_2007 ======+====== IOR Foot Model 2007 ======
  
 **This tutorial describes the 2007 publication. For the updated 2014 IOR foot model [[Visual3D:Tutorials:Modeling:IOR_Foot_Model|see here]]**. **This tutorial describes the 2007 publication. For the updated 2014 IOR foot model [[Visual3D:Tutorials:Modeling:IOR_Foot_Model|see here]]**.
Line 26: Line 26:
 === Multi-Segment Foot Marker Set === === Multi-Segment Foot Marker Set ===
  
-{{foot_markersIOR.png}}+{{:foot_markersIOR.png}}
  
 CA<sup>[[#cite_note-Leardini-1|[1]]]</sup>(FCC) <sup>[[#cite_note-Serge-2|[2]]]:p. 160</sup> = Posterior Surface of Calcaneus CA<sup>[[#cite_note-Leardini-1|[1]]]</sup>(FCC) <sup>[[#cite_note-Serge-2|[2]]]:p. 160</sup> = Posterior Surface of Calcaneus
Line 43: Line 43:
 === Landmarks === === Landmarks ===
  
-|**1. Create RMET_DIST:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RMET_DIST//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RMET_DIST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RFMH//\\    **Ending Point:** //RVMH//\\    **Lateral Object:** //RSMB//\\    **Project From:** //RSMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RMET_DIST.png}}|+|**1. Create RMET_DIST:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RMET_DIST//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RMET_DIST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RFMH//\\    **Ending Point:** //RVMH//\\    **Lateral Object:** //RSMB//\\    **Project From:** //RSMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RMET_DIST.png}}|
  
 === Segment Definition === === Segment Definition ===
  
-|**1. Create RMet Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RMet// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Select **Kinematic Only**<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RMet** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSMB//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RMET_DIST//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RFMH//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RFMB//, //RFMH//, //RSMB//, //RSMH//, //RVMB//, //RVMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RMET.png}}|+|**1. Create RMet Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RMet// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Select **Kinematic Only**<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RMet** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSMB//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RMET_DIST//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RFMH//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RFMB//, //RFMH//, //RSMB//, //RSMH//, //RVMB//, //RVMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RMET.png}}|
  
 \\ \\
  
  
-|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RMET_SCS.png}}|+|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RMET_SCS.png}}|
  
 The image to the right (and all other images in this tutorial) show a mediolateral view of the segment coordinate system after it has been modified. The image to the right (and all other images in this tutorial) show a mediolateral view of the segment coordinate system after it has been modified.
Line 60: Line 60:
 === Landmarks === === Landmarks ===
  
-|**1. Create RID Joint Center:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RID//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RID//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RTN//\\    **Ending Point:** //RVMB//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RID.png}}|+|**1. Create RID Joint Center:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RID//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RID//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RTN//\\    **Ending Point:** //RVMB//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RID.png}}|
  
 === Segment Definition === === Segment Definition ===
  
-|**1. Create RMid Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RMid// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Select **Kinematic Only**.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RMid** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RID//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSMB//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RTN//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RSMB//, //RTN//, //RVMB//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Segment_RMID.png}}|+|**1. Create RMid Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RMid// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Select **Kinematic Only**.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RMid** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RID//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSMB//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RTN//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RSMB//, //RTN//, //RVMB//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Segment_RMID.png}}|
  
 \\ \\
  
  
-|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RMID_SCS.png}}|+|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RMID_SCS.png}}|
  
 ==== Calcaneus (Cal) ==== ==== Calcaneus (Cal) ====
Line 75: Line 75:
 === Landmarks === === Landmarks ===
  
-|**1. Create RIC Joint Center:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RIC//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RIC//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RST//\\    **Ending Point:** //RPT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RIC.png}}|+|**1. Create RIC Joint Center:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RIC//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RIC//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RST//\\    **Ending Point:** //RPT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RIC.png}}|
  
 === Segment Definition === === Segment Definition ===
  
-|**1. Create RCal Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RCal// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RCal** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RCA//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RIC//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RCA//, //RPT//, //RST//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Segment_RCAL.png}}|+|**1. Create RCal Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //RCal// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **RCal** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RCA//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RIC//     **Medial:** //None//     \\    **Radius:** //0.1//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RCA//, //RPT//, //RST//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Segment_RCAL.png}}|
  
 \\ \\
  
  
-|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RCAL_SCS.png}}|+|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RCAL_SCS.png}}|
  
 ==== Foot (Foo) ==== ==== Foot (Foo) ====
Line 90: Line 90:
 === Landmarks === === Landmarks ===
  
-|**1. Create RFT_DIST:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RFT_DIST//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RFT_DIST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RCA//\\    **Ending Point:** //RFMH//\\    **Lateral Object:** //RVMH//\\    **Project From:** //RSMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RFT_DIST.png}}|+|**1. Create RFT_DIST:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RFT_DIST//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RFT_DIST//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RCA//\\    **Ending Point:** //RFMH//\\    **Lateral Object:** //RVMH//\\    **Project From:** //RSMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RFT_DIST.png}}|
  
 === Segment Definition === === Segment Definition ===
  
-|**1. Create Right Foot Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //Right Foot// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **Right Foot** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RCA//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RST,RPT)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RFT_DIST//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RFMH,RVMH)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RFMH//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RCA//, //RFMH//, //RVMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Segment_RFT.png}}|+|**1. Create Right Foot Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //Right Foot// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **Right Foot** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RCA//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RST,RPT)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RFT_DIST//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RFMH,RVMH)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Medial//     //RFMH//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RCA//, //RFMH//, //RVMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Segment_RFT.png}}|
  
 \\ \\
  
  
-|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RFT_SCS.png}}|+|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+Y//\\    **Distal to Proximal:** //-X//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RFT_SCS.png}}|
  
 ==== Shank (Sha) ==== ==== Shank (Sha) ====
Line 105: Line 105:
 === Landmarks === === Landmarks ===
  
-|**1. Create RIM:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RIM//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RIM//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RLM//\\    **Ending Point:** //RMM//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RIM.png}}|+|**1. Create RIM:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RIM//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RIM//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RLM//\\    **Ending Point:** //RMM//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //0.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RIM.png}}|
  
-|**2. Create RSK_PROX:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RSK_PROX//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RSK_PROX//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RIM//\\    **Ending Point:** //RLM//\\    **Lateral Object:** //RHF//\\    **Project From:** //RTT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Landmark_RSK_PROX.png}}|+|**2. Create RSK_PROX:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RSK_PROX//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RSK_PROX//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RIM//\\    **Ending Point:** //RLM//\\    **Lateral Object:** //RHF//\\    **Project From:** //RTT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Landmark_RSK_PROX.png}}|
  
 === Segment Definition === === Segment Definition ===
  
-|**1. Create Right Shank Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //Right Shank// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **Right Shank** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSK_PROX//     **Medial:** //None//     \\    **Radius:** //DISTANCE(RSK_PROX,RHF)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RIM//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RLM,RMM)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RLM//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RHF//, //RLM//, //RMM//, //RTT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Segment_RSK.png}}|+|**1. Create Right Shank Segment:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>In the **Segments** tab, select //Right Shank// in the Segment Name box.<HTML></li></HTML>\\ <HTML><li></HTML>Click on the **Create Segment** button.<HTML></li></HTML>\\ <HTML><li></HTML>In the **Right Shank** tab, enter these values:\\ \\ |<HTML><p></HTML>   **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RSK_PROX//     **Medial:** //None//     \\    **Radius:** //DISTANCE(RSK_PROX,RHF)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Distal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RIM//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RLM,RMM)//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RLM//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Select Tracking Targets:**\\      //RHF//, //RLM//, //RMM//, //RTT//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>\\ <HTML><li></HTML>Click on **Close Tab** before proceeding.<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Segment_RSK.png}}|
  
 \\ \\
  
  
-|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+X//\\    **Distal to Proximal:** //+Y//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Seg_RSK_SCS.png}}|+|**2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define the Segment Orientation as:\\ \\ |<HTML><p></HTML>   **A/P Axis:** //+X//\\    **Distal to Proximal:** //+Y//\\ <HTML></p></HTML>||<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Seg_RSK_SCS.png}}|
  
 ==== Angles ==== ==== Angles ====
Line 124: Line 124:
 The F2Pt and F2Ps planar angles are calculated as the angle between the lines created by the targets FMB-FMH and FMH-PM. To calculate this angle using the Compute Planar Angle command, an offset along the line between FMB and FMH is created to define the 3 point angle. The F2Pt and F2Ps planar angles are calculated as the angle between the lines created by the targets FMB-FMH and FMH-PM. To calculate this angle using the Compute Planar Angle command, an offset along the line between FMB and FMH is created to define the 3 point angle.
  
-|**1. Create RF2P_Offset:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RF2P_Offset//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RF2P_Offset//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RFMB//\\    **Ending Point:** //RFMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //1.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{LandmarkImage_RF2P_Offset.png}}|+|**1. Create RF2P_Offset:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RF2P_Offset//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RF2P_Offset//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //RFMB//\\    **Ending Point:** //RFMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **AXIAL** Offset: //1.5//<HTML></li></HTML>\\ <HTML><li></HTML>**Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:LandmarkImage_RF2P_Offset.png}}|
  
 \\ \\
Line 139: Line 139:
  
  
-|**3. Create Lab_O:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_O//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_O//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.0//    **Y:** //0.0//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{IORFoot_Lab_O.png}}|+|**3. Create Lab_O:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_O//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_O//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.0//    **Y:** //0.0//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IORFoot_Lab_O.png}}|
  
 \\ \\
  
  
-|**4. Create Lab_X:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_X//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_X//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.05//    **Y:** //0.0//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{IORFoot_Lab_X.png}}|+|**4. Create Lab_X:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_X//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_X//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.05//    **Y:** //0.0//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IORFoot_Lab_X.png}}|
  
 \\ \\
  
  
-|**5. Create Lab_Y:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_Y//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.0//    **Y:** //0.05//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{IORFoot_Lab_Y.png}}|+|**5. Create Lab_Y:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //Lab_Y//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //Lab_Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //0.0//    **Y:** //0.05//    **Z:** //0.0//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IORFoot_Lab_Y.png}}|
  
 \\ \\
  
  
-|**6. Create RFMH_proj:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RFMH_proj//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RFMH_proj//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //LAB_O//\\    **Ending Point:** //LAB_X//\\    **Lateral Object:** //LAB_Y//\\    **Project From:** //RFMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{IORFoot_RFMH_proj.png}}|+|**6. Create RFMH_proj:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Click **Landmarks** button<HTML></li></HTML>\\ <HTML><li></HTML>Click **Add New Landmark** button<HTML></li></HTML>\\ <HTML><li></HTML>Create Landmark: //RFMH_proj//\\ \\ |<HTML><p></HTML>   **Landmark Name:** //RFMH_proj//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Define Orientation Using:**\\    **Starting Point:** //LAB_O//\\    **Ending Point:** //LAB_X//\\    **Lateral Object:** //LAB_Y//\\    **Project From:** //RFMH//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%)//<HTML></li></HTML>\\ <HTML><li></HTML>**Do NOT Check:** //Calibration Only Landmark//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IORFoot_RFMH_proj.png}}|
  
 \\ \\
Line 173: Line 173:
  
  
-|**1. Create RF2Pt planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2Pt//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //LANDMARK::ORIGINAL::RF2P_offset//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RPM//\\ **Angle Direction:** //Left Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RF2Pt.png}}|+|**1. Create RF2Pt planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2Pt//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //LANDMARK::ORIGINAL::RF2P_offset//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RPM//\\ **Angle Direction:** //Left Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RF2Pt.png}}|
  
 \\ \\
Line 185: Line 185:
  
  
-|**1. Create RS2F planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2F//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMH//\\    2 - //TARGET::ORIGINAL::RSMB//\\    3 - //TARGET::ORIGINAL::RFMB//\\    4 - //TARGET::ORIGINAL::RFMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RS2F.png}}|+|**1. Create RS2F planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2F//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMH//\\    2 - //TARGET::ORIGINAL::RSMB//\\    3 - //TARGET::ORIGINAL::RFMB//\\    4 - //TARGET::ORIGINAL::RFMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RS2F.png}}|
  
 \\ \\
Line 197: Line 197:
  
  
-|**1. Create RS2V planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2V//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMH//\\    2 - //TARGET::ORIGINAL::RSMB//\\    3 - //TARGET::ORIGINAL::RVMB//\\    4 - //TARGET::ORIGINAL::RVMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RS2V.png}}|+|**1. Create RS2V planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2V//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMH//\\    2 - //TARGET::ORIGINAL::RSMB//\\    3 - //TARGET::ORIGINAL::RVMB//\\    4 - //TARGET::ORIGINAL::RVMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XZ//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RS2V.png}}|
  
 \\ \\
Line 212: Line 212:
  
  
-|**1. Create RF2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RFMB//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RFMH_proj//\\    4 - //TARGET::ORIGINAL::RFMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RF2G.png}}|+|**1. Create RF2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RFMB//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RFMH_proj//\\    4 - //TARGET::ORIGINAL::RFMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RF2G.png}}|
  
 \\ \\
Line 227: Line 227:
  
  
-|**1. Create RS2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMB//\\    2 - //TARGET::ORIGINAL::RSMH//\\    3 - //TARGET::ORIGINAL::RSMH_proj//\\    4 - //TARGET::ORIGINAL::RSMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RS2G.png}}|+|**1. Create RS2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RS2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RSMB//\\    2 - //TARGET::ORIGINAL::RSMH//\\    3 - //TARGET::ORIGINAL::RSMH_proj//\\    4 - //TARGET::ORIGINAL::RSMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RS2G.png}}|
  
 \\ \\
Line 242: Line 242:
  
  
-|**1. Create RV2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RV2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RVMB//\\    2 - //TARGET::ORIGINAL::RVMH//\\    3 - //TARGET::ORIGINAL::RVMH_proj//\\    4 - //TARGET::ORIGINAL::RVMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RV2G.png}}|+|**1. Create RV2G planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RV2G//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **4 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RVMB//\\    2 - //TARGET::ORIGINAL::RVMH//\\    3 - //TARGET::ORIGINAL::RVMH_proj//\\    4 - //TARGET::ORIGINAL::RVMB_proj//\\ **Angle Direction:** //Right Hand Rule//\\ **3D Space:** //Always 0 to 180 degrees//\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RV2G.png}}|
  
 \\ \\
Line 258: Line 258:
  
  
-|**1. Create RF2Ps planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2Ps//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //LANDMARK::ORIGINAL::RF2P_offset//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RPM//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XY//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RF2Ps.png}}|+|**1. Create RF2Ps planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RF2Ps//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //LANDMARK::ORIGINAL::RF2P_offset//\\    2 - //TARGET::ORIGINAL::RFMH//\\    3 - //TARGET::ORIGINAL::RPM//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XY//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RF2Ps.png}}|
  
 \\ \\
Line 271: Line 271:
  
  
-|**1. Create RMLA planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RMLA//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RCA//\\    2 - //TARGET::ORIGINAL::RST//\\    3 - //TARGET::ORIGINAL::RFMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XY//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{PlanarAngle_RMLA.png}}|+|**1. Create RMLA planar angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Define **Resulting Signal** Name: //RMLA//<HTML></li></HTML>\\ <HTML><li></HTML>Calculate a **3 point angle** between the following targets:\\ \\ |<HTML><p></HTML>   1 - //TARGET::ORIGINAL::RCA//\\    2 - //TARGET::ORIGINAL::RST//\\    3 - //TARGET::ORIGINAL::RFMH//\\ **Angle Direction:** //Right Hand Rule//\\ **Use Range:** //-180 to 180 degrees//\\ **Projected onto Plane:** //XY//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>**Note: The reference segment will need to be changed to //RMet// within the text option.**\\ <HTML></p></HTML>  ||<HTML></li></HTML><HTML></ol></HTML>  |  {{:PlanarAngle_RMLA.png}}|
  
 \\ \\
Line 282: Line 282:
 == Sha_Foo_Angle == == Sha_Foo_Angle ==
  
-|**1. Define the RSha_Foo_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RSha_Foo_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //Right Foot//\\    **Reference Segment:** //Right Shank//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Foot_RSha_Foo_Angle.png}}|+|**1. Define the RSha_Foo_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RSha_Foo_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //Right Foot//\\    **Reference Segment:** //Right Shank//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Foot_RSha_Foo_Angle.png}}|
  
 == Sha_Cal_Angle == == Sha_Cal_Angle ==
  
-|**1. Define the RSha_Cal_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RSha_Cal_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RCal//\\    **Reference Segment:** //Right Shank//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Foot_RSha_Cal_Angle.png}}|+|**1. Define the RSha_Cal_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RSha_Cal_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RCal//\\    **Reference Segment:** //Right Shank//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Foot_RSha_Cal_Angle.png}}|
  
 == Cal_Mid_Angle == == Cal_Mid_Angle ==
  
-|**1. Define the RCal_Mid_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RCal_Mid_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMid//\\    **Reference Segment:** //RCal//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Foot_RCal_Mid_Angle.png}}|+|**1. Define the RCal_Mid_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RCal_Mid_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMid//\\    **Reference Segment:** //RCal//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Foot_RCal_Mid_Angle.png}}|
  
 == Mid_Met_Angle == == Mid_Met_Angle ==
  
-|**1. Define the RMid_Met_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RMid_Met_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMet//\\    **Reference Segment:** //RMid//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Foot_RMid_Met_Angle.png}}|+|**1. Define the RMid_Met_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RMid_Met_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMet//\\    **Reference Segment:** //RMid//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Foot_RMid_Met_Angle.png}}|
  
 == Cal_Met_Angle == == Cal_Met_Angle ==
  
-|**1. Define the RCal_Met_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RCal_Met_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMet//\\    **Reference Segment:** //RCal//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{IOR_Foot_RCal_Met_Angle.png}}|+|**1. Define the RCal_Met_Angle:**\\ \\ <HTML><ol></HTML>\\ <HTML><li></HTML>Open the **Compute Model Based** dialog<HTML></li></HTML>\\ <HTML><li></HTML>Select **JOINT_ANGLE** from drop down list\\ \\ |<HTML><p></HTML>   **Data Name:** //RCal_Met_Angle//\\ <HTML></p></HTML>\\ \\ <HTML><p></HTML>   **Segment:** //RMet//\\    **Reference Segment:** //RCal//\\    **Cardan Sequence:** //Z-X-Y//\\ <HTML></p></HTML>||<HTML></li></HTML>\\ <HTML><li></HTML>**Use Negative**:\\    **X:** //TRUE//    **Y:** //TRUE//    **Z:** //FALSE//<HTML></li></HTML><HTML></ol></HTML>  |  {{:IOR_Foot_RCal_Met_Angle.png}}|
  
 ==== References ==== ==== References ====
visual3d/tutorials/modeling/ior_foot_model_2007.1720028751.txt.gz · Last modified: 2024/07/03 17:45 by sgranger