HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » pipeline » event_commands » Event Global Maximum
visual3d:documentation:pipeline:event_commands:event_global_maximum

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:pipeline:event_commands:event_global_maximum [2025/04/28 15:37] – wikisysopvisual3d:documentation:pipeline:event_commands:event_global_maximum [2025/04/28 17:39] (current) – [Dialog] wikisysop
Line 38: Line 38:
 |**/RESULT_EVENT_NAME=**           | Name of the event that will be created at the frame where the signal reaches its global maximum. | |**/RESULT_EVENT_NAME=**           | Name of the event that will be created at the frame where the signal reaches its global maximum. |
 |**!/SIGNAL_TYPES=**               | The type of signal being analyzed (e.g., `ANALOG`, `LINK_MODEL_BASED`, `TARGET`). | |**!/SIGNAL_TYPES=**               | The type of signal being analyzed (e.g., `ANALOG`, `LINK_MODEL_BASED`, `TARGET`). |
-|**!/SIGNAL_FOLDER=**              | Folder the signal is pulled from, e.g., `ORIGINAL`, `PROCESSED`, etc. |+|**!/SIGNAL_FOLDER=**              | Folder the signal is pulled from (e.g., `ORIGINAL`, `PROCESSED`, etc.). |
 |**!/SIGNAL_NAMES=**               | Label(s) of the signal(s) to analyze (e.g., `Left_Knee_Angle`). | |**!/SIGNAL_NAMES=**               | Label(s) of the signal(s) to analyze (e.g., `Left_Knee_Angle`). |
 |**!/SIGNAL_COMPONENTS=**          | Specific components (X, Y, Z) or index of the signal vector to use. | |**!/SIGNAL_COMPONENTS=**          | Specific components (X, Y, Z) or index of the signal vector to use. |
Line 56: Line 56:
  
 {{:visual3d:documentation:pipeline:event_commands:egm_dialog.png?500|}} {{:visual3d:documentation:pipeline:event_commands:egm_dialog.png?500|}}
 +
 +  * **New Event Label Name**: Name for the event that will be created at the global maximum.
 +  * **Signal Component**: Signal direction selection (X, Y, Z).
 +  * **Frame Offset**: Number of frames to shift the created event forward or backward from the maximum point.
 +  * **Time Offset**: Shifts event by time (in seconds).
 +  * **Threshold**: Min. signal value required to accept a maximum.
 +  * **Event Sequence and Instance for range**: Search for maximum based on event ranges.
 +  * **Subsequence and Instance within the Event Sequence**: Search inside a sub-range within the event sequence.
  
  
Line 75: Line 83:
  
  
-=== Example 1: Simple Use Case ===+==== Example 1: Simple Use Case ====
 This example will be done showing both the dialog box and corresponding command text. This example will be done showing both the dialog box and corresponding command text.
  
Line 123: Line 131:
 ---- ----
  
-=== Example 2: Exclude Sequence ===+==== Example 2: Exclude Sequence ====
  
 In this example an event **BAD** was created between one sequence of **RHS + RHS**. Using the same parameters as the previous example, set the **Exclude Sequences containing events** parameter to **BAD** In this example an event **BAD** was created between one sequence of **RHS + RHS**. Using the same parameters as the previous example, set the **Exclude Sequences containing events** parameter to **BAD**
Line 152: Line 160:
 ---- ----
  
-=== Example 3: Subsequence ===+==== Example 3: Subsequence ====
  
 Subsequences can be used to create an event that occurs within a sequence within a sequence. Subsequences can be used to create an event that occurs within a sequence within a sequence.
  
-In this example **RKFlex_Max** was created as the maximum value between **LTO + LHS** when these events feel between the **RHS** events.+In this example **RKFlex_Max** was created as the maximum value between **LTO + LHS** when these events fall between the **RHS** events.
  
 Using the same parameters as the previous example, set the **Subsqeuence** parameter to **LTO + LHS** Using the same parameters as the previous example, set the **Subsqeuence** parameter to **LTO + LHS**
visual3d/documentation/pipeline/event_commands/event_global_maximum.1745854658.txt.gz · Last modified: 2025/04/28 15:37 by wikisysop