Differences

This shows you the differences between two versions of the page.

--- visual3d:documentation:modeling:segments:pelvis_segment_angle [2024/06/26 20:23] – created sgranger
+++ visual3d:documentation:modeling:segments:pelvis_segment_angle [2024/08/26 19:36] (current) – [Examples] wikisysop
@@ Line 1: / Line 1: @@
-====== Pelvis_Segment_Angle ======
+====== Pelvis Segment Angle ======
 The Pelvis Angle typically refers to the orientation of the Pelvis relative to the Laboratory.
@@ Line 48: / Line 48: @@
 Let's create the following landmarks:
-Landmark Name= **Lab_Origin**
+Landmark Name= **Lab_Origin**\\
-Starting Point= Enter nothing
+Starting Point= Enter nothing\\
-Existing Segment= **LAB**
+Existing Segment= **LAB**\\
-Offset Using the Following ML/AP/AXIAL Offset= X=**0** , Y=**0** , Z=**0**
+Offset Using the Following ML/AP/AXIAL Offset= X=**0** , Y=**0** , Z=**0**\\
 Calibration Only Landmark= Leave Unchecked
-Landmark Name= **Lab_Anterior**
-Starting Point= Enter nothing
+Landmark Name= **Lab_Anterior**\\
-Existing Segment= **LAB**
+Starting Point= Enter nothing\\
-Offset Using the Following ML/AP/AXIAL Offset= X=**0.707** , Y=**0.707** , Z=**0**
+Existing Segment= **LAB**\\
-Calibration Only Landmark= Leave Unchecked
+Offset Using the Following ML/AP/AXIAL Offset= X=**0.707** , Y=**0.707** , Z=**0**\\
-Landmark Name= **Lab_Z**
-Starting Point= Enter nothing
-Existing Segment= **LAB**
-Offset Using the Following ML/AP/AXIAL Offset= X=**0** , Y=**0** , Z=**0.1**
 Calibration Only Landmark= Leave Unchecked
+Landmark Name= **Lab_Z**\\
+Starting Point= Enter nothing\\
+Existing Segment= **LAB**\\
+Offset Using the Following ML/AP/AXIAL Offset= X=**0** , Y=**0** , Z=**0.1**\\
+Calibration Only Landmark= Leave Unchecked\\
 Let's create the Virtual Lab Segment:
-In the Segment Name combo box type **Virtual Lab**
+In the Segment Name combo box type **Virtual Lab**\\
-Select Segment Type = **Visual3D**.
+Select Segment Type = **Visual3D**.\\
-**Check the Kinematic Only Check Box**
+**Check the Kinematic Only Check Box**\\
-Select the **Create** button
+Select the **Create** button\\
-In the Segment dialog box, enter the following:
+In the Segment dialog box, enter the following:\\
+Define Proximal Joint and Radius\\
+Lateral= None Joint= **Lab_Z** Medial=None Radius= **0.01**\\
+Define Distal Joint and Radius\\
+Lateral= None Joint= **Lab_Origin** Medial= None Radius= **0.01**\\
+Extra Target To Define Orientation (if needed)\\
+Location= **Anterior** and **Lab_Anterior**\\
+**Select Tracking Markers same as Calibration Markers**\\
-Define Proximal Joint and Radius
-Lateral= None Joint= **Lab_Z** Medial=None Radius= **0.01**
-Define Distal Joint and Radius
-Lateral= None Joint= **Lab_Origin** Medial= None Radius= **0.01**
-Extra Target To Define Orientation (if needed)
-Location= **Anterior** and **Lab_Anterior**
-**Select Tracking Markers same as Calibration Markers**
 When creating the pelvis segment angle, select this Virtual Lab as the reference segment.