HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » modeling » segments » Knee Alignment Device
visual3d:documentation:modeling:segments:knee_alignment_device

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:modeling:segments:knee_alignment_device [2024/07/12 14:01] – created sgrangervisual3d:documentation:modeling:segments:knee_alignment_device [2025/03/18 18:41] (current) – wikisysop
Line 1: Line 1:
-====== Knee_Alignment_Device ======+====== Knee Alignment Device ======
  
 The Knee Alignment Device (KAD) is manufactured by [[https://www.motion-labs.com/index.html|Motion Lab Systems]] and is described [[https://www.motion-labs.com/prod_qa_kad.html|here]]. The KAD is used to assist in defining the frontal plane of the thigh segment. It is manufactured by Motion Lab Systems to precise definition (5.66 inches or 0.143764 meters between markers). The markers that are provided with the KAD have 24.8 mm markers attached. The KAD is used in the standing trial, and the origin of the KAD is replaced by a marker on the lateral knee located at the intersection of the 3 posts. The Knee Alignment Device (KAD) is manufactured by [[https://www.motion-labs.com/index.html|Motion Lab Systems]] and is described [[https://www.motion-labs.com/prod_qa_kad.html|here]]. The KAD is used to assist in defining the frontal plane of the thigh segment. It is manufactured by Motion Lab Systems to precise definition (5.66 inches or 0.143764 meters between markers). The markers that are provided with the KAD have 24.8 mm markers attached. The KAD is used in the standing trial, and the origin of the KAD is replaced by a marker on the lateral knee located at the intersection of the 3 posts.
  
-{{labs.com/prod_qa_kad.html|{{/images/thumb/8/8f/KAD_Image_From_MLS.png}}+{{:labs.com/prod_qa_kad.html}}|{{/images/thumb/8/8f/KAD_Image_From_MLS.png}}
  
 ===== Marker Diameter ===== ===== Marker Diameter =====
Line 11: Line 11:
 In the [[https://www.motion-labs.com/prod_qa_kad.html|KAD]] distributed by Motion Lab Systems, this diameter matches that of the markers on the original KAD (24.8 mm). How the diameter value is used, is further described in this [[https://www.has-motion.com/download/examples/KAD/KAD_Marker_Radius.pptx|power point]]. In the [[https://www.motion-labs.com/prod_qa_kad.html|KAD]] distributed by Motion Lab Systems, this diameter matches that of the markers on the original KAD (24.8 mm). How the diameter value is used, is further described in this [[https://www.has-motion.com/download/examples/KAD/KAD_Marker_Radius.pptx|power point]].
  
-{{4|{{/images/thumb/8/8c/KAD_Image_From_GaitPosture.png}}+{{:4|{{/images/thumb/8/8c/KAD_Image_From_GaitPosture.png}}
  
 ===== Tutorial ===== ===== Tutorial =====
Line 30: Line 30:
   * LKD1, LKD2, LKAX   * LKD1, LKD2, LKAX
  
-{{KAD1.jpg}}+{{:KAD1.jpg}}
  
 \\ \\
Line 39: Line 39:
 In the Models tab, under Subject Data/Metrics, click "Add New Item" to create each of the following metrics: In the Models tab, under Subject Data/Metrics, click "Add New Item" to create each of the following metrics:
  
-{{SubjectDataMetrics.png}}+{{:SubjectDataMetrics.png}}
  
 \\ \\
Line 47: Line 47:
   - **Value or Expression:** //DISTANCE(RKD1,RKD2)/SQRT(2)//   - **Value or Expression:** //DISTANCE(RKD1,RKD2)/SQRT(2)//
  
-{{KAD_Length.png}}+{{:KAD_Length.png}}
  
 **NOTE:** This equation is described here. **NOTE:** This equation is described here.
Line 58: Line 58:
   - **Value or Expression:** //0.0248//   - **Value or Expression:** //0.0248//
  
-{{KAD_Marker_Diameter.png}}+{{:KAD_Marker_Diameter.png}}
  
 **3.** Create Model Metric **RKnee_Diameter**, which is the width of the knee (distance between the mediolateral borders of the knee). This metric should be taken manually during the data collection: **3.** Create Model Metric **RKnee_Diameter**, which is the width of the knee (distance between the mediolateral borders of the knee). This metric should be taken manually during the data collection:
Line 65: Line 65:
   - **Value or Expression:** //0.125//   - **Value or Expression:** //0.125//
  
-{{KAD_RKnee_Diameter.png}}+{{:KAD_RKnee_Diameter.png}}
  
 **NOTE:** The knee diameter will be different for each subject. **NOTE:** The knee diameter will be different for each subject.
Line 76: Line 76:
 2. Check the **Kinematic Only** Check Box 2. Check the **Kinematic Only** Check Box
 3. Select the **Create** button 3. Select the **Create** button
-{{KAD2.jpg}}+{{:KAD2.jpg}}
  
 2. In the **RKD** tab, enter these values: 2. In the **RKD** tab, enter these values:
Line 83: Line 83:
 5. Click on **Build Model.** 5. Click on **Build Model.**
 6. Click on **Close Tab** before proceeding. 6. Click on **Close Tab** before proceeding.
-{{KAD4.jpg}}+{{:KAD4.jpg}}
  
 The resulting segment coordinate system is displayed. The z-axis (blue line) of the KAD segment coordinate system is parallel to the KAD axis. The resulting segment coordinate system is displayed. The z-axis (blue line) of the KAD segment coordinate system is parallel to the KAD axis.
  
-{{KAD5.jpg}}+{{:KAD5.jpg}}
  
 ==== Step 3: Create a landmark at the origin of the KAD. ==== ==== Step 3: Create a landmark at the origin of the KAD. ====
Line 108: Line 108:
 <HTML></li></HTML> <HTML></li></HTML>
 <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML> <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>
-<HTML><li></HTML><HTML><p></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))// {{KAD6.jpg}} The resulting landmark should appear at the origin of the KAD in the 3D viewer. {{KAD7.jpg}}<HTML></p></HTML>+<HTML><li></HTML><HTML><p></HTML>**Do NOT Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))// {{:KAD6.jpg}} The resulting landmark should appear at the origin of the KAD in the 3D viewer. {{:KAD7.jpg}}<HTML></p></HTML>
 ==== Step 4: Create a landmark at the Knee Joint Center ==== ==== Step 4: Create a landmark at the Knee Joint Center ====
  
Line 125: Line 125:
 <HTML></li></HTML> <HTML></li></HTML>
 <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML> <HTML><li></HTML>**Do NOT Check:** //Offset by Percent (1.0 = 100%) (Meters when not checked)//<HTML></li></HTML>
-<HTML><li></HTML><HTML><p></HTML>**Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))// {{KAD_RT_KNEE_STATIC.png}} The resulting landmark should appear in the 3D viewer. {{KAD10.jpg}}<HTML></p></HTML>+<HTML><li></HTML><HTML><p></HTML>**Check:** //Calibration Only Landmark (Not generated for assigned motion file(s))// {{:KAD_RT_KNEE_STATIC.png}} The resulting landmark should appear in the 3D viewer. {{:KAD10.jpg}}<HTML></p></HTML>
 ==== Step 5: Create a Right Thigh Segment ==== ==== Step 5: Create a Right Thigh Segment ====
  
Line 134: Line 134:
 <HTML><p></HTML>2. In the Segment Type combo box select **CODA**<HTML></p></HTML> <HTML><p></HTML>2. In the Segment Type combo box select **CODA**<HTML></p></HTML>
 <HTML><p></HTML>3. Select the **Create** button<HTML></p></HTML> <HTML><p></HTML>3. Select the **Create** button<HTML></p></HTML>
-<HTML><p></HTML>{{KAD_PelvisCreate.png}}<HTML></p></HTML>+<HTML><p></HTML>{{:KAD_PelvisCreate.png}}<HTML></p></HTML>
 <HTML><p></HTML>4. In the **Pelvis** dialog, enter these values:<HTML></p></HTML> <HTML><p></HTML>4. In the **Pelvis** dialog, enter these values:<HTML></p></HTML>
 |   **R.ASIS** //RASIS//\\ \\    **L.ASIS** //LASIS//\\ \\    **R.PSIS** //RPSIS//\\ \\    **L.PSIS** //LPSIS//\\ \\    **Select Tracking Targets:**\\ \\       **Check:** //Use Calibration Targets for Tracking//|| |   **R.ASIS** //RASIS//\\ \\    **L.ASIS** //LASIS//\\ \\    **R.PSIS** //RPSIS//\\ \\    **L.PSIS** //LPSIS//\\ \\    **Select Tracking Targets:**\\ \\       **Check:** //Use Calibration Targets for Tracking//||
Line 140: Line 140:
 <HTML><p></HTML>5 Click on **Build Model.**<HTML></p></HTML> <HTML><p></HTML>5 Click on **Build Model.**<HTML></p></HTML>
 <HTML><p></HTML>6.Click on **Close Tab** before proceeding.<HTML></p></HTML> <HTML><p></HTML>6.Click on **Close Tab** before proceeding.<HTML></p></HTML>
-<HTML><p></HTML>{{KAD_Pelvis.png}}<HTML></p></HTML>+<HTML><p></HTML>{{:KAD_Pelvis.png}}<HTML></p></HTML>
 <HTML><p></HTML>**2. Create the Right Thigh:**<HTML></p></HTML> <HTML><p></HTML>**2. Create the Right Thigh:**<HTML></p></HTML>
 <HTML><ol></HTML> <HTML><ol></HTML>
Line 151: Line 151:
 <HTML></li></HTML> <HTML></li></HTML>
 <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML> <HTML><li></HTML>Click on **Build Model.**<HTML></li></HTML>
-<HTML><li></HTML><HTML><p></HTML>Click on **Close Tab** before proceeding. {{KAD_RightThigh.png}} In this implementation the frontal plane of the thigh segment is defined by the Hip Joint Center at the Knee Alignment Device. There are many other ways that the frontal plane can be defined, including specifying the THIGH marker as the lateral object. {{KAD12.jpg}}<HTML></p></HTML>+<HTML><li></HTML><HTML><p></HTML>Click on **Close Tab** before proceeding. {{:KAD_RightThigh.png}} In this implementation the frontal plane of the thigh segment is defined by the Hip Joint Center at the Knee Alignment Device. There are many other ways that the frontal plane can be defined, including specifying the THIGH marker as the lateral object. {{:KAD12.jpg}}<HTML></p></HTML>
 ===== References ===== ===== References =====
  
visual3d/documentation/modeling/segments/knee_alignment_device.1720792901.txt.gz · Last modified: 2024/07/12 14:01 by sgranger