Differences

This shows you the differences between two versions of the page.

--- visual3d:documentation:modeling:modeling_overview [2024/07/12 13:28] – removed sgranger
+++ visual3d:documentation:modeling:modeling_overview [2026/02/02 15:44] (current) – Revised Model Subject Metrics section. wikisysop
@@ Line 1: / Line 1: @@
+====== Modelling Overview ======
+At the core of Visual3D is the development of a flexible biomechanical modelling tool that can be used to define an unrestricted number of rigid segments and link them together in a systematic fashion. These segments may be linked implicitly through the motion capture data (e.g. segments in the experiment probably didn't disarticulate) or explicitly through the specification of constraints.
+  - The first scenario is handled in Visual3D by assuming that each segment is mathematically independent of all other segments, i.e., a [[visual3d:documentation:kinematics_and_kinetics:six_degrees_of_freedom|Six Degrees of Freedom]] model.
+  - The second scenario is handled by allowing the specification of joint constraints and implementing an [[Visual3D:Documentation:Kinematics_and_Kinetics:Inverse_Kinematics#Inverse_Kinematics_Overview|Inverse Kinematics]]) approach.
+**NOTE**: For markerless motion capture systems, Visual3D was updated in early 2021 to handle the [[visual3d:documentation:c3d_signal_types:rotation_data_type|rotation matrices]] needed to automatically build models. Customers who have not maintained Visual3D software support may need to contact HAS-Motion and restart the software support in order to get newer versions of Visual3D.
+===== Assign Model to Motion File =====
+Allows the user to specify which model is to be applied to a movement trial.
+{{:ModelMenu2.jpg}}
+Visual3D allows many movement trials to be applied to one model, but only one model file may be applied to a movement trial.
+A movement trial that has not been assigned to a model will not have segments.
+===== A Segment =====
+A segment is a rigid object defined geometrically by a [[Visual3D:Documentation:Modeling:Segments:Segment_Coordinate_System|local coordinate system]] and a length. Each segment is treated as ideally rigid, i.e., it does not deform in response to applied forces, and is allowed to exist anywhere in space.
+Visual3D assumes that the local coordinate system is capable of moving in space, so it is assumed that a sensor is attached to the segment to track this movement. The motion capture system (regardless of the type) tracks the position and/or orientation of the sensor and Visual3D computes the **pose** (position and orientation) of the segment from the transformation between sensor coordinates, segment coordinates, and joint constraints. The term sensor is used very loosely here because Visual3D actually assumes that markers are attached rigidly to a segment, or that a segment is connected to other segments by a "joint". Visual3D will not allow a segment to be defined that doesn't not include a tracking sensor.
+==== Segment Properties ====
+A segment may have, but does not necessarily have to have, inertial properties.
+The [[Visual3D:Documentation:Modeling:Segments:Segment_Properties#Segment_Mass|default mass]] is based on [[https://deepblue.lib.umich.edu/handle/2027.42/4540|Dempster's regression equations]].
+The [[Visual3D:Documentation:Modeling:Segments:Segment_Properties#Segment_Inertia|default moment of inertia and location of center of mass]] are computed assuming that a [[Visual3D:Documentation:Modeling:Segments:Segment_Properties#Segment_Geometry|segment has a geometrical shape]] (cylinder, cone, sphere, ellipsoid).
+Optionally, the user may specify explicitly the inertial properties of the segment.
+A segment may have, but does not necessarily have to have, a decoration.
+The default decorations are a surface model which is rendered for the animation. These [[Visual3D:Documentation:Modeling:Segments:Segment_Properties#Animation_Surface_Models|surface models]] can be specified as either an [[Visual3D:Documentation:Modeling:Segments:Segment_Properties#Wavefront_obj_file_format|Alias Wavefront .obj]] format or VRML .wrl format. This decoration is exclusively ornamental, and has no affect on the kinematics or kinetics of the segment.
+===== Model Subject Metrics =====
+The subject data tab allows for subject measurements, subject information, and scalar data related to segment calibration to be entered.
+[[visual3d:documentation:modeling:model_metrics|Subject Data]] may be defined as a floating point value, string, or an [[Visual3D:Documentation:Pipeline:Expressions:Expressions_Overview|expression]]. To create a new Subject Data item, click the Add New Item button. This will bring up a dialog to enter the new subject data Name and its value or expression. This Subject Data is available to be used in other model dialogs as part of an [[Visual3D:Documentation:Pipeline:Expressions:Expressions_Overview|expression]].
+===== Note on the Conventional Gait Model ======
+The Conventional Gait Model refers to the marker set (both unilateral and bilateral), the algorithms used to estimate the pose (position and orientation) of the segments, and to the conventions for representing model based items (joint angles and joint moments). This marker set was defined 35 years ago and was largely a result of inadequate technology rather than the best placement of markers. We prefer to think of this marker set as The Legacy Gait Model because presented with a better alternative, most knowledgeable users naturally evolve from this limited representation.